Simple  type  CO2 Atomizer

    3 in 1  multifunctional CO2 Diffuser

 

         CO2 Diffuser + Check Valve + CO2 Calculator       

 

NEW5.gif (2638 bytes)
   PATENT PRODUCTS
10peso.gif (821 bytes)
 PATENT FEATURES :

1.  Including check valve to avoid adverse current

2. Observing and controlling the flowing amount of CO2  after adding water into the diffuser

3.      Conjoining the air tube fixer to prevent the air outlet from bending


INSTRUCTIONS:

1.  Remove the lid, take the ceramic diffuser piece out and fill the diffuser with water; then put the ceramic diffuser piece and lid back to the diffuser.

2. Connect the CO2 diffuser with CO2 supply pipe; then place the air tube onto the fixer.

3.  Fix the sucker onto the diffuser, and put the diffuser into the fish tank.

*  It's a normal phenomena for the grains to be thicker at first use. In a few hours the grains will become thinner. After a long term usage, when the grains become thicker and fewer, please replace a new ceramic diffuser piece for better performance.

R-125  CO2 Atomizer  (S)

R-126   CO2 Atomizer (L)

  

28 ∮mm x 52 mm

42 ∮mm x 62 mm

ceramic diffuser piece:  16 ∮mm

ceramic diffuser piece:  27 ∮mm

  

 

 

CO2 Diffuser Accessories

 

R-127    Ceramic diffuser piece + Sucker

R-128   Ceramic diffuser piece + Sucker

FOR  R-125  Simple  type  CO2 Atomizer

FOR  R-126  Simple  type  CO2 Atomizer

CHECK VALVE + CO2 CALCULATOR

 

                       (used both inside and outside the tank) 

 

  
NEW5.gif (2638 bytes)
  Instructions:

1.Infuse water into this check valve

2. When used inside the tank, install the sucker and attach it to the tank wall. Connect the air-in hole with CO2 supply pipe; connect the air-out hole with CO2 diffuser.

3. When used outside the tank, apply the same method except the sucker part.

R-120   

CHECK VALVE + CO2 CALCULATOR 

 

R-131   BUBBLE COUNTER WITH INTEGRATED CHECK VALVE

(can be used both inside or outside of the tank)

  
NEW5.gif (2638 bytes)
  Instructions:

1. Pour water into the unit. The water level should not be higher than the black rubber ring.

2. To install in the interior, attach the suction cup onto the tank wall. Connect the CO2 supply pipe to the inlet connector and connect the CO2 diffuser to the outlet connector.

3. To install on the exterior, fasten the hook onto the unit, then hang the unit on the tank. Apply the same procedures as when installing in the interior.

R-131  D:26 ∮mm x L: 100 mm

CHECK VALVE + CO2 CALCULATOR 

 

R-131A   R-131B  

    SUPREME POWER CYCLONE   CO2  DISSOLUTION  ~   

                    


AQUARIUM CO2 AND WATER DISSOLUTION REACTOR
NEW5.gif (2638 bytes)
 PATENT ：TAIWAN. JAPAN. U .S .A
10peso.gif (821 bytes)
PATENT SPECIFICATION :
10peso.gif (821 bytes)
 1. CO2 quantity is observed and controlled by the measuring device.
10peso.gif (821 bytes)
2. CO2 and water are guided into the impeller and mixed by the power head transport.
10peso.gif (821 bytes)
3. Mixed CO2 and water are stirred through the special rotating track then diffused. Eventually, the water will be re-stirred cyclonically in the reacting cartridge.
10peso.gif (821 bytes)
4. If there is escaped gas, it is guided through the inhale inlet into the impeller then re-stirred. The waste gas (N) will be released from the outlet on the top of the measuring device.


FEATURE :
10peso.gif (821 bytes)
 1. Complete unit with Submerge Power Head and the diffuser.
10peso.gif (821 bytes)
 2. Easy installation, minimum space required. The color looks like water plants and can beautify circumstances.
10peso.gif (821 bytes)
 3. Display the quantity of CO2.
10peso.gif (821 bytes)
 4. The water diffused from the bottom outlet is already mixed with CO2.
10peso.gif (821 bytes)
5. Sponge inside Supreme Cyclone CO2 Dissolution Reactor also acts as a filter.
10peso.gif (821 bytes)
 6. Besides the original function, Supreme Cyclone can be used as power head.
10peso.gif (821 bytes)
 SPECIFICATIONS : Attach:  Ceramic Shaft  and Anisotropic magnet inside.   Flow: 1000L/H      Watts: 10W

A-33  CO2  DISSOLUTION (S) A-33 Package A-34  CO2  DISSOLUTION (L) A-34 Package
Accessories for A-34

X-76 Sponge for A-34 

X-110 Canister for A-34 

A-34-a Complete Canister for A-34

    CO2  REGULATOR ~

MODEL

Information

R-70 CHECK VALVE & BUBBLE CONTROL
  R-71 CHECK VALVE & BUBBLE CONTROL
R-72 SIMPLE  CO2 REGULATOR
R-72-1 MINI SIMPLE  CO2 REGULATOR
R-73 SIMPLE  SINGLE METER CO2 REGULATOR
R-73-1 MINI SIMPLE  SINGLE METER CO2 REGULATOR
R-75 DUAL METER CO2  SOLENOID  REGULATOR
R-76 DUAL METER CO2  SOLENOID  REGULATOR
R-77 DUAL METER CO2  SOLENOID  REGULATOR

R-70    

R-71

 

R-72 

R-72 -1

R-72 & R-72-1

 R-73  

R-73-1

  R-73    &    R-73-1

 

R-75   Single Outlet (Aluminum Material)

R-76   Single Outlet ( Copper material )

R-77   Six Outlet ( Copper material )

 

  UNDERWATER PLANT SCISSORS (NIPPER&CLIPPER)

R-89  Underwater plant scissors (steel head clipper)  L:70cm

   steel head clipper

Underwater plant scissors (steel head clipper) 

This series product is from the “Plastic rod+ Plastic nippers” and the usages and structures are the same.

Features and functions:

1. The clipper is made of steel and the rod is made of A-class plastic.

2. It can clip aquatic very easily. 

Usages: To manipulate with rod and trigger.

1. Push the trigger forward slightly. When the trigger is over the plot, you can take away the clippers easily.

2. Putting the clippers into the head of rod, pulling the trigger into position. Then it works.