eg-new

Products

SIMPLE TYPE CO₂ ATOMIZER

3 in 1 multifunctional CO₂ Diffuser

CO₂ Diffuser + Check Valve + CO₂ Calculator

   PATENT PRODUCTS

PATENT FEATURES :
1.      Including check valve to avoid adverse current
2.      Observing and controlling the flowing amount of CO₂ after adding water into the diffuser

3.      Conjoining the air tube fixer to prevent the air outlet from bending

INSTRUCTIONS:
1.      Remove the lid, take the ceramic diffuser piece out and fill the diffuser with water; then put the ceramic diffuser piece and lid back to the diffuser.

2.      Connect the CO₂ diffuser with CO₂ supply pipe; then place the air tube onto the fixer.

3. Fix the sucker onto the diffuser, and put the diffuser into the fish tank.

* It's a normal phenomena for the grains to be thicker at first use. In a few hours the grains will become thinner. After a long term usage, when the grains become thicker and fewer, please replace a new ceramic diffuser piece for better performance.


R-125 CO₂ Atomizer 28 ∮mm x 52 mm	R-126 CO₂ Atomizer 42 ∮mm x 62 mm
ceramic diffuser piece: 16 ∮mm	ceramic diffuser piece: 27 ∮mm

CHECK VALVE + CO₂CALCULATOR

(used both inside and outside the tank)

Instructions:

1.Infuse water into this check valve

2. When used inside the tank, install the sucker and attach it to the tank wall. Connect the air-in hole with CO₂supply pipe; connect the air-out hole with CO₂ diffuser.

3. When used outside the tank, apply the same method except the sucker part.

R-120

CHECK VALVE + CO₂CALCULATOR

SALTWATER Hydrometer ~

MULTI FUNCTIONAL ~

Hydrometer &Digital Thermometer

Patent Features:
1.Almost no bubbles.
2.Inside mountable for continuous reading.
3.View temperature and specific gravity simultaneously.
4.Use continuously or periodically.

R-10

SIMPLE ~Hydrometer Patent Features: 1.Almost no bubbles. 2.Easy to use 3.Easy to read 4.High precision
	R-10-1

GENERAL ~ Hydrometer
Patent Features:
1.Almost no bubbles.
2.Inside mountable for continuous reading.
3.Use continuously or periodically.

R-10-2

*SIMPLE* SALTWATER Hydrometer Patent Features: 1.Almost no bubbles. 2.Easy to use 3.Easy to read 4.High precision Direction： Holding the top of the unit, slowly place it into the aquarium. Water will begin to flow in through inlets 1 & 2 on the upper sides of the unit. When water flows above the water-filled conduits, you can read the specific gravity on the inside scale.
	R-15

*GENERAL* SALTWATER Hydrometer Patent Features: 1.Almost no bubbles. 2.Inside mountable for continuous reading. 3.Use continuously or periodically.
	R-16

NEW6.gif (1680 bytes) CHECK VALVE ~

NEW PATENT PRODUCT:
1. Use CHECK VALVE when the air pump is set below the level of the water.

2. Patent design prevents off side stress from water and prolongs the life of the check valve.

DIRECTION :

1. The position of the CHECK VALVE is as illustrated.

2. The side with an arrow linked with the necessary equipment besides the tank; the other side is linked with the air pump.


S-45 2pcs/card	S-45-1 1pc/card	S-45-2 (Bulk)
(24card/box)	(24card/box)

Mini CHECK VALVE ~


S-92 12pcs/card	S-92-1 (Bulk)	S-92-1 S-45-2
S-92 12pcs/card	SIZE: D:13∮ x L: 35 mm	S-92-1 S-45-2

NEW6.gif (1680 bytes) TWIN (2 in 1) ~ AIR STONE + CHECK VALVE

NEW PATENT PRODUCT

1. Use TWIN (Check valve and Air stone), when the air pump is in use.

2. Especially, use TWIN when the air pump is set below the level of the water.

SPECIFICATION:
1.Air Stone, with plastic materials, can resist corrosion. In addition, the inside valve is made of silicon so it can extend the life.

2.TWIN, with the uniform air in, can make the double effect. Please feel the ease to use the patent valve.

3.TWIN can be used for any size of air pump.


S-46 2pcs/card 25x22 mm φ	S-46-1 1pc/card 25x22 mm φ	S-46-2 (Bulk) 25x22 mm φ
(24card/box)	(24card/box)

Mini TWIN ~


S-90 12pcs/card	S-90-1 (BULK)	S-91 12pcs/card	S-91-1 + suction cup (BULK)
	SIZE: D:16∮ x L:15 mm		SIZE: D:16∮ x L:15 mm

OZONIZER (MORE OXYGEN) ~

Savior of tropical fish and sea water fish Fish inhabit the natural world where they have large space to live. However, they only have small space when living in an aquarium. If we don't improve their habitat, it is predicted that a large proportion of fish would be in danger. Ozonizer is the most efficient equipment to process water, sterilize water, prevent and cure disease. You don't have to add any other medicine during use. It is clean without residue. Moreover, it helps enhance color and brightening of fish. Most of all, it makes you enjoy your life more.
	A-13
FEATURE : 1. Prevent Disease: Using ozonizer one to two hours a day can prevent fish from diseases. If the feedstuff can be processed by ozonizer in advance, it is helpful to keep diseases away. 2. Cure Disease: Effective for white spot, rotten fin or muddy water. Use ozonizer one hour a day three times for 7-8 days. If the diseases mentioned above are not too serious, fish will recover soon. 3. Can Neutralize NO2: NO2 is made from the decomposition of fish's excreta and surplus feedstuff. NO2 up to 1 centigram per liter will endanger the fish . Meanwhile, much NO2 may cause the death of fish . Using ozonizer can neutralize NO2. 4. Clean and De-color water: Congeal organisms and granules of water and make water clean. It is more effective to be used in combination with "PROTEN SKIMMER". De-color the dirty water caused by man-made feedstuff. 5. How much O3 is suitable: (Refer to the following table) Regulate the quantity of O3 from minimum to a little smell of ozone on the surface of water. It is suitable to use ozonizer for 30 minutes to two hours. There is no harm to humans. A little O3 spread in the air helps clean the air. 6. Attention: Store in a dry and less dusty place Dry and clean air helps promote the life of ozonizer. 7. Electric Power: VOLTAGE 110V 60Hz POWER 7 WATT. Notice: 1. Don't use ozonizer in a closed room. 2. Pay attention to the circulation of air during use. 3. Because of high voltage inside, please don't take ozonizer apart by yourself.

NEW6.gif (1680 bytes)
MORE OXYGEN + TIMER

Savior of Fresh & Sea Tropical Fish
Function : Kill the Germs; Get rid of bad smell; Get rid of toxin.

Direction:

1: Connect the outlet of AIR PUMP to the "IN" on OZONIZER, and connect the AIR STONE to the "OUT", and put it into the water.

2: Adjust the "OZ-150" to the density which is needed, and then adjust the "TIMER" to set up the time which is needed.

3: Plug in and press the "POWER" to "1" and the light of power is on, and then press "START" so the red light is on, and the OZONIZER will start to operate.

4: When the red light of "START" is lambent, it means that the time you set is up and the OZONIZER won't operate. So if you need to use it again, turn off the power first and turn on it again then press "START".

5: If you want to use OZONIZER continually, please turn the "TIMER" to the "CONTD" (THE FIRST GRID). If you don't want to use it anymore, you can press "POWER" to "0", and the light of power will damp, and the OZONIZER will stop.

6: If you don't want to use it anymore, just press down.

A-15

TANK L×W×H(cm)	TANK L×W×H(feet)	Capacity of water (liter)	Degree of ozonizer (ppm)	Timer (min)
61×46×46	2'×1'6"×1'6"	110	20	15
76×46×46	2'5"×1'6"×1'6"	140	20	30
91×46×46	3'×1'6"×1'6"	170	20	60
121×46×46	4'×1'6"×1'6"	225	30	120
121×46×46	4'×1'6"×2'	300	40	120
152×60×60	5'×2'×2'	490	60	180
152×61×76	5'×2'×2'6"	630	70	180
182×61×61	6'×2'×2'	600	70	240
182×76×76	6'×2'6"×2'6"	950	100	240
210×76×76	7'×2'6"×2'6"	1200	130	300
1PPM=3000cc/min (air pump) Please double the time of use for sea water fish. What is listed is general data It might be adjusted according to the clarity of water and quantity of fish....etc. *The Accuracy of Timer : ±1%

WATER TESTING ~ PH

PH-999 DIGITAL METER

●INTRODUCTIONS: 1. Fix the PH sensor in the water gently. 2. Plug in and wait for approx.15 Min., the number indicating on the meter is the PH value of the water . ●NOTES: 1.The PH sensor consists of a sensitive glass sensor and combined with a silver/silver chloride sensor. The plastic body is light-proof and hard enough to avoid broken.The sensor should not be kept out of the water for a long time. If the PH sensor need to be taken away from the aquarium, the sensor should be stored in the original plastic bottle, which filled with KCL-solution. 2.Clean the glass bulb of PH sensor regularly (every two or three months) to avoid the impurities and lint brought into the water. 3. It can not be used in non-aqueous solution. 4.The glass bulb of the PH sensor should be soaked in a storage bottle filled with KCL-solution to keep it moist when the PH meter is not working. PS. PH measuring range: 1- 9.9 PH Temperature range: 5 - 60°C
	R-12

	PH 7.0 Correct Liquid (Bar)

PH-998 DIGITAL METER

● Instruction Guide: 1.Please remove the sensor from the protective bottle ,and rinse the surface with taping water. (If the solution in the protective bottle is lost and the glass bulb of the sensor is dry, please soak the tip of the sensor in storage solution. (PH=7.0) or taping water buffer for at least two hours prior to using it ) 2.Connect the BNC connector to the PH meter and fix the tip of the glass bulb in the aqua box with sucker. 3.Plug in and wait for 5 minutes ,the PH value of the water will display on the meter. NOTES: 1.It is normal for white crystallization on the glass bulb or sensor body. 2.(If inside liquid is not GEL) Shake the sensor down as with a clinical thermometer to eliminate any air bubbles inside the sensor. 3.Periodically (for example 3-6months) clean the sensor, by leaving it soaking for 10-15 minutes in taping water. 4.After cleaning the sensor, calibrating the meter will be necessary. Soak the tip of the sensor for 2-3 minutes in the PH=7.0 buffer solution, then adjust the "adj" trimmer on the front panel of PH meter to PH7.0 with the attached screwdriver.. 5.The glass bulb of the PH sensor should be soaked in a storage bottle filled with KCL-solution to keep it moist when the PH meter is not working. P.S. The BNC connector is re movable.
	R-12-1

	PH 7.0 Correct Liquid (Bar)

Microprocessor-based testers ~ PH & ORP

R-29 Microprocessor-based PH testers

R-30 Microprocessor-based O R P testers

Range: 2.0~12.0 PH

Accuracy: ±0.2 PH

Operating Temp.: 5°C~50°C

Power Supply: DC 2x 3V (button battery)

Battery Life: ＞150hrs

Size (LxWxH): 147x 28x15mm

Weight: 50g

Range: ± 999mv

Resolution: 1mv

Accuracy(20°C): ± 5mv

Power Supply: DC 2x 3V (button battery)

Battery Life: ＞150hrs

Size (LxWxH): 147x 28x15mm

Weight: 50g

NEW6.gif (1680 bytes)

M. I. T. HEATER ~

IC THERMO ADJ. HEATER ( 2 IN 1 )

(Stop heating in the air)

Patent Features: 1.The expected temperature can be adjusted on the plug. You don't have to adjust it in water any more. 2.Sensor is rested outside of the glass in the heater tube. Sensor can directly measure the correct water temperature in the aquarium and keep heating water to the expected temperature value. 3.Plastic protection is added to the silica glass heater tube which can avoid breakage. 4.It will switch off automatically when it is out of water. Direction: 1.Submerge the heater entirely into water. 2.Use the enclosed sucking disc to fix the heater in the tank. Connect the power supply and the light shows green. 3.Adjust the expected temperature on the plug. 4.When the light shows red, the water temperature is lower than the expected temperature. 5.When the red light turns off, the water temperature has reached the expected value. 6.When the water temperature is lower than the expected value, heater will switch on automatically. 7.The heater will switch off automatically when it is out of water. Precautions: 1: Water sensor "+" and "-" should be sunk under the water together as to activate the heater. 2:The heater should be placed in flowing current. 3:Please pull out the plug while changing water or doing maintenance work of the fish tank. 4:Take the heater out of water 5 minutes after it cools down.
	D-52 100W D-53 200W D-54 300W

	2 IN 1 SETTING TEMP.

IC THERMO ADJ. HEATER (Seperate)

with Setting Temp. Device

Patent Features: 1.The expected temperature can be switched on "Setting Temp" device. 2.Sensor is rested outside of the glass in the heater tube. Sensor can directly measure the correct water temperature in the aquarium and keep heating water to the expected temperature value. 3.Plastic protection is added to the silica glass heater tube which can avoid breakage. 4.It will switch off automatically when it is out of water. Direction: 1.Submerge the heater entirely into water. 2.Use the enclosed sucking disc to fix the heater in the tank. Connect the power supply and the light shows green. 3.Adjust the expected temperature on the "Setting Temp". 4.When the light shows red, the water temperature is lower than the expected temperature. 5.When the red light turns off, the water temperature has reached the expected value. 6.When the water temperature is lower than the expected value, heater will switch on automatically. 7.The heater will switch off automatically when it is out of water. Precautions: 1: Water sensor "+" and "-" should be sunk under the water together as to activate the heater. 2:The heater should be placed in flowing current. 3:Please pull out the plug while changing water or doing maintenance work of the fish tank. 4:Take the heater out of water 5 minutes after it cools down.
	D-52B 100W D-53B 200W D-54B 300W

	SETTING TEMP.

NEW6.gif (1680 bytes)

F .I .R. HEATER

IC -THERMO ADJ. HEATER (2 in 1)

PATENT SPECIFICATIONS:
1 The expected temperature can be adjusted on the plug. You don't have to adjust it in water any more.
2 Sensor is rest on the outside of the glass of the heater tube. So, Sensor can directly measure the more correct water temperature in the aquarium. As a result, it can keep supplying energy to the expected temperature value.
3 Plastic protection is added to the outside of the silica glass heater tube, that can avoid breakage.

SPECIFICATION:
1.Submerge the heater entirely into water.
2.Use the enclosed sucking disc to fix the heater in the tank. Connect the power supply and the light shows green.
3.Adjust the expected temperature on the "Setting Temp".
4.When the light shows red, the water temperature is lower than the expected temperature.
5.When the red light turns off, the water temperature has reached the expected value.
6.When the water temperature is lower than the expected value, heater will switch on automatically.

D-49 100W D-50 200W D-51 300W

IC -THERMO ADJ. HEATER (Seperate)

with Setting Temp. Device

PATENT SPECIFICATIONS:
1 The expected temperature can be adjusted on the "Setting Temp" device. You don't have to adjust it in water any more.
2 Sensor is rest on the outside of the glass of the heater tube. So, Sensor can directly measure the more correct water temperature in the aquarium. As a result, it can keep supplying energy to the expected temperature value.
3 Plastic protection is added to the outside of the silica glass heater tube, that can avoid breakage.

D-49B 100W D-50B 200W D-51B 300W

NEW6.gif (1680 bytes)

T. R. S. HEATER~

29°C(84°F) FIXED TEMP. HEATER (BLUE)

SPECIFICATION:

1. Pre-set temperature.
2. Easy installation.
3. Safe & precise operation.

Direction:

1.Submerge the heater entirely into water.
2.Use the enclosed sucking disc to fix the heater in the tank. Connect the power supply..
3.When the light shows red, the water temperature is lower than the expected temperature.
4.When the red light turns off, the water temperature has reached the expected value.
5.When the water temperature is lower than the expected value, heater will switch on automatically to the fixed temperature.

Welcome Aquarium inquire. Temp setting could be appointed..

D-46 100W D-47 200W D-48 300W

29°C(84°F) FIXED TEMP. HEATER (GREEN)

SPECIFICATION:

1. Pre-set temperature.
2. Easy installation.
3. Safe & precise operation.

Direction:

Welcome Aquarium inquire. Temp setting could be appointed..

D-46B 100W D-47B 200W D-48B 300W

Reptile Animal Use ~


R-39 Sticker Thermometer	R-40 Sticker Hygrometer
Diameter: 5cmØ	Diameter: 5cmØ
Range: 0ºC~50ºC (40ºF~120ºF)	Range: 0%~100%

CATALOG